D-Link DSL-G624T Guía de usuario Pagina 47
- Pagina / 97
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
DSL-G624T Wireless A DSL Router User’s Guide
Static IP Address for Connection WAN
When the Router is configured to use Static IP
Address assignment for the WAN connection,
you must manually assign a global IP Address,
Subnet Mask and Gateway IP Address used fo
r
the WAN connection. Most users will also nee
d
to configure DNS server IP settings in the DNS
Settings configuration menu (see below). Follow
the instruction below to configure the Router to
use Static IP Address assignment for the WAN
connection.
To configure a Dynamic IP Address connection,
perform the steps listed below. Some of the
settings do not need to be changed the first time
the device is set up, but can be changed later i
f
you choose. See the table below for a description
of all the settings available in this menu.
WAN Settings - Static IP
1. Choose the Static IP Address option from the WAN Settings pull-down menu.
2. Under the ATM VC Settings at the top of the menu should not be changed unless you have been instructed to
change them. However, if you are instructed to change the VPI or VCI values, type in the values assigned for
your account. Leave the PVC and Virtual Circuit setting at the default (Pcv0 and Enabled) values for now. This
can be used later if you are configuring multiple virtual circuits for your ADSL service. For more information on
ATM VC Settings, see the table on page 42 below.
3. Under the Static IP heading, choose the Connection Type from the pull-down menu. This defines both the
connection type and encapsulation method used for your ADSL service. The available options are Bridged IP
LLC, Bridged IP VC-MUX, Routed IP LLC, Routed IP VC-MUX or IPoA.. If have not been provided specific
information for the Connection Type setting, leave the default setting.
4. Change the IP Address, Subnet Mask, Gateway Address and (if available) Secondary DNS Server IP address
as instructed by your ISP. These are the global IP settings for the WAN interface. This is the “visible” IP address
of your account. Your ISP should have provided these IP settings to you. For IPoA (Classic IP over ATM)
connections you may need to type in an additional IP address for a ARP Server Address. If you are using an
IPoA connection, ask your ISP if it is necessary to use an ARP (Address Resolution Protocol) server.
5. Leave the MTU value at the default setting (default = 1400) unless you have specific reasons to change this (see
table below).
6. NAT should remain enabled. If you disable NAT, you not be able to use more than one computer for Internet
connections. NAT is enabled and disabled system-wide, therefore if you are using multiple virtual connections,
NAT will disabled on all connections.
39
- DSL-G624T 1
- Wireless ADSL Router 1
- User’s Guide 1
- Table Of Contents 3
- Before You Start 5
- Packing List 6
- Installation Requirements 6
- Additional Software 7
- Introduction 9
- Front Panel Display 12
- Rear Panel Connections 13
- Wireless LAN Basics 14
- About 802.11g Wireless 15
- Hardware Installation 16
- Factory Reset Button 17
- Wired Network Connections 17
- Power on Router 17
- Basic Router Configuration 20
- Windows 2000 23
- Windows 95 and Windows 98 23
- Windows ME 24
- Windows NT 4.0 Workstations 24
- Login to Home Page 25
- Configure the Router 26
- Using the Setup Wizard 27
- Wireless LAN Setup 35
- Wireless Security 36
- WEP Encryption 38
- Configure WPA Settings 39
- Configure WAN Connection 41
- Bridged Connection for WAN 46
- ATM Traffic Shaping 49
- ATM VC Settings 50
- LAN IP Settings 51
- Use the Router for DHCP 52
- 53
- Disable the DHCP Server 53
- DNS Server Settings 54
- Dynamic DNS 55
- Save Settings and Reboot 56
- Advanced Router Management 57
- Virtual Server 59
- LAN Clients 61
- Filters 63
- Bridge Filters 65
- Routing 66
- Firewall 68
- ATM VCC 72
- Wireless Management 74
- Wireless Performance 75
- Change System Password 77
- Remote Log 79
- Firmware 81
- Ping Test (Miscellaneous) 82
- Status Information 84
- Device Information Display 85
- DHCP Clients 86
- Traffic 88
- Technical Specifications 90
- IP Address Setup 92
- Using DHCP 93
- IP Concepts 94
- Subnet Mask 95
- Micro Filters and Splitters 96
- Split Line Filter 97
Relacionado con productos y manuales para Puntos de acceso wlan D-Link DSL-G624T
Puntos de acceso wlan D-Link DIR-601 Manual de usuario
(115 paginas)
(115 paginas)
Puntos de acceso wlan D-Link DP-313 - Air 802.11b Wireless Print Server Especificaciones
(83 paginas)
(83 paginas)
Puntos de acceso wlan D-Link DWL-2210AP Especificaciones
(192 paginas)
(192 paginas)
Puntos de acceso wlan D-Link DSL-G604T Especificaciones
(110 paginas)
(110 paginas)
Seagate TS-EC880 Pro manuály
Uživatelské manuály a uživatelské příručky pro NAS a úložné servery Seagate TS-EC880 Pro.
Poskytujeme 1 manuály pdf Seagate TS-EC880 Pro ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentarios a estos manuales